My experimental 3D printer didn’t come with a heated bed. Luckily I had this round ceramic heater laying around. With a bit of kapton tape I got this:
I got this cute little 3D printer from the local MicroCenter two days ago. I know, I know, not everyone has MicroCenter around.
Anyhow, the printer is Wanhao Duplicator I3 Mini, it is OEM made for MicroCenter as “PowerSpec” brand. It is not the pinnacle of engineering, but it is quite amazing when it comes to cost cutting. Very minimal design – just the basics, but quite usable.
It has this cute front panel with graphic LCD:
I believe Monoprice sells a version of this printer with better features. It’s a good choice if you are looking to get into the hobby and don’t want to break the bank. The Monoprice version is $50 more expensive, but has way better features like heated bed and wifi support.
Here is a “torture test” I printed with the printer in it’s stock configuration with the sample filament that came with it. It is not bad at all.
The main reason I got this printer was to test my 3D printer controller board (open source designs on github.com here). I wanted something small that would fit on my desk and this printer was an excellent choice. Naturally I butchered it to connect my controller:
After a day of tweaking the Marlin firmware, I managed to get it to work:
I printed for about 3 hour yesterday, constantly checking the motor drivers for overheating, but they were not even breaking a sweat.
The motors are very quiet, unlike my screeching power supply on the video. Next, I’ll have to design a box for the controller, it is quite unsightly sitting like that with all cables.
New revision (rev1) of my 3D printer controller board arrived a few weeks ago from the board manufacturer (http://jlcpcb.com). I did assemble a prototype with one driver for “smoke test”. Well it did “smoke” only a bit, because I accidentally put one chip in reverse. Lucky for me it was not the Trinamic driver – that one survived.
Anyhow today I made another board – this time with all components populated. Here is how it went up.
Mounted the PCB in an improvised jig to keep it secure on my table. The “jig” is made from 4 small PCBs from a different project. I secured them with blue tape, so they hold the main PCB in place.
Next was aligning the kapton stencil on top of the PCB. The stencil is made by http://oshstencil.com It is not aligned yet.
Here it is aligned on top of the board and secured with another piece of blue tape:
Getting ready to apply solder paste. I use “credit card” squeegee from OshStencil.
Paste away. I usually put too much, but it is easier to have some left over, than scraping the last bit of paste over and over again.
Here it is – paste applied. You can see that my footprint for TR3 needs to be fixed – the paste opening is way too big. Oh well – rev2 I guess.
By the way because my stencil application jig is not particularly sturdy you can see the solder paste is smudged over the fine point IC pads. It is not the end of the world. It makes a few solder bridges, but easily fixable. It is better, when I use solder paste printer, but I don’t have a framed stencil for this board they are $$$.
And it goes in the CHMT48VB pick-and-placer.
And the machine goes – here is a short video clip of the beginning of the job. Note that the board is split in two jobs. The second job is with different set of nozzles. I don’t have the nozzle change in the video – sorry.
The board after all components are placed by the machine. I use the machine only for tedious parts. I place other components by hand.
After manually placing the rest of the SMD parts, the board is ready for solder re-flow. I use hot air gun. I have a T962 oven, but it always seems like too much effort to use it. Here is the result of my hot air application. You can see quite a few bridges on the drivers. Click on the picture for full resolution image.
All cleaned up
Now to solder all true-hole connectors. This is the most tedious and time consuming part. Here it is all done. Front:
I did a quick check and there are no shorts on any power supply lanes. On to testing the firmware.
After a few idle weeks, I finally decided to order the current rev1 of the TMC2130 board design. I found this web site (pcbshopper.com) which compares the price of various PCB manufacturers and matches them with your board specifications.
As luck would have it, a day after I sent the files to the board manufacturer (jlcpcb for the rev1), I had an idea of adding thermocouple interface.
Here is the rev2 of the board with dual thermocouple connectors. It should work with MAX31856, MAX31855 as well as the good old MAX6675 chips. All of these are based on some form of SPI interface, and I just added them to the bus.
Because I used all I/O pins, if you decide you need thermocouples, you’ll have to sacrifice the two controllable extruder cooling fans. Most 3d printers come with “always on” cooling fans anyway.
The thermocouple connectors use generic SPI(MISO, MOSI, SCK, CS) + 5V power and GND pins. In theory one could connect other things, with appropriate software patch.
I’m growing very fond of the 3D rendering in KiCad. It is scary realistic and made me realize I made a few errors with components on top of each other.
This is the back of the board where the STM32 NUCLEO-64 board is plugged in.
In my previous tests my PrntrBoard prototype was having some issues talking to the TMC2130 motor driver chip. It took a while, but I figured out the issue – the SPI library was not initializing correctly, so the chip was using the SPI0, hardware block, while on my board the drivers are hooked to SPI1 pins.
A few configuration settings later and Marlin was booting up, without complaining. In the process of debugging I also created a small test program to control the motor driver. You can see it here.
From that work I found that the motor driver chip was getting quite hot if I set the motor current at 900mA. The default was 600mA – it was getting warm but not as bad. Anyhow I decided I want to further stress the thermal design of the board and ordered this 4 channel thermometer.
The thermometer arrived today and I set to use it for a few tests. Keep in mind the accuracy of the thermometer is questionable at this point. I did a very simple test:
- at ambient room temperature all 4 channels showed values within 0.3 degree Celsius.
- I held all 4 probes in my hand and all 4 showed 35.1C – again within 0.2C of each other.
First I tried to test the extruder heater control logic. From previous attempts I know it was working, but I wanted to see how accurate the temperature is. I set the printer to heat the E1 to 180C:
M104 T1 S180
This is a video from that test. My thermometer shower 163.5C or thereabouts – so there is a significant offset between the firmware and the thermometer. I also verified with an infrared thermometer and it was showing ~160C. So it seems the thermistor setting is not quite correct. The bad thing is that this heater came from China and I have no clue what thermistor they used, so I’ll have to measure it a few times to determine the correct parameters that should go in the firmware. That would be a post on its own.
Disappointed from my temperature control test, I set to test the thermal design of the board. I added a thermocouple to the bottom of the board – where the motor driver ship is mounted.
as well as a second thermocouple on top of the chip
This was to test a theory, which suggested that the chip dissipates more heat on the bottom side.
Attempt one was not very conclusive. This was using Marlin, I enabled the extruder motor and with the default settings it had 600mA of drive current and 300mA standby current, but this was not enough. The driver chip was barely at 30C and both top and bottom were at similar temperature.
Attempt two almost ended in a disaster. I used the above test program to make the motor running with 900mA drive current, but the program had an unfortunate side effect of leaving the extruder heater on. I smelled smoke and turned the power off. The smoke smell was from the extruder heater melting the temperature probe cable.
Crisis averted and on to attempt number three. My test program was spinning the motor, the power consumption was about 0.5A at 12V. The chip was heating with steady rate, even with my big fan blowing over the board. It was clear the board would not sustain such current. However the top and bottom of the chip were within 1-2C of each other. I decided that maybe the fan was interfering with the measurements and thus ensued attempt number five.
The chip was heating rapidly, but finally you can see the top was 5C hotter than the bottom. Another observation was how quickly things cooled down after the power was turned off.
After all this what is the conclusion:
- the motor driver does get hot on the top, so putting a radiator on the top has some merit
- my thermal design sucks, and I decided to re-route the bottom of the board, so there is a large copper area with no traces which can dissipate the heat from the chip.
- the thermistor coefficient needs to be calibrated in the firmware
- on the bright side almost all controls are working and Marlin is operational to a degree.
Well, ’till next time
PrntrBoard is a 3D printer controller board designed to work with STM32 NUCLEO dev kits. The current version (V1) supports NUCLEO-64 series kits. The design is being developed on F446-RE kit, but other models could work as well. IMO the STM32F446 NUCLEO-64 kit offers very good performance (180MHz CPU) for the price ($15).
Some features of the board:
- 5x Trinamic super quiet drivers (TMC2130 or TMC2660)
- Marlin firmware
- 4x controllable fans and 2x “always on” fan connectors
- selectable fan voltage (5V or Vin)
Because the NUCLEO-64 has limited number of IO pins, some compromises had to be made:
- No sd-card
- No display support
Generic shortcuts I don’t plan to improve:
- 5V power supply is external. These are available from various resellers and fairly cheap – less than $1. No need to waste board layout space and component count.
- Heated bed MOSFET – large heated beds consume a lot of power, and it is challenging to provision the design for > 10A current. External heated bed MOSFETs are very affordable < $10 and claim to support 20A minimum. If you have large bet use one.
I use the daily build of KiCad (soon to be released V5) – let me know if you have trouble opening the files.
Once the design is validated I would add support for NUCLEO-144 kits, these have many more available I/O pins, which would enable more extruders, SD-card and LCD screen utilities to be added. The downside is that they are quite big and I’m trying to limit the design to 10x10cm to reduce the cost of the PCB fabrication.
The current design is using 4 layer board, 6/6 mil clearance, 12 mil via hole size and 20 mil via diameter.
There are two active branches:
- tmc2130 – the board design for TMC2130 series drivers
- master – the board design for TMC2660 drivers
Both PCB designs use the QFP version of the driver ICs because they can handle a bit more power.
I have made prototypes of the TMC2130 board design (rev0) – the board has a few bugs, that are corrected in the rev1 version. I have validated the heaters, and fan controls are operational. Working the kinks out of the motor driver wiring.
The TMC2660 branch status is: the rev0 board is fully routed and passes DRC checks. I have not made any prototypes of the board, because 2660 drivers are hard to find due to low stock levels at suppliers.
The software for the board is a clone of Marlin at bugfix-2.0.x branch of my repository. I keep it relatively in sync with the Marlin branch. Note: there are other branches of Marlin as well only the bugfix-2.0.x supports the STM32 microcontroller.
Marlin is using Arduino IDE or Platform IO. I personally had issues with Platform IO not supporting the STM32F4 board, so I use Arduino version 1.8.5. To compile the firmware code, you would need to install the STM32 Arduino port.
Leave a comment if you have any questions.